Parker Standard Pilot Assisted Load Control Valves (CB101CF30V)
Part Number
CB101CF30V
Parker’s piloted load holding/counterbalance valves are a combination of a relief, sequence, and flow control valve that can handle pressures up to 420 bar (6000 psi) and flows up to 350 lpm (90 gpm). These robust valves allow the operator to maintain control of the load by preventing it from overrunning the pump while also protecting against thermal expansion. The wide selection of pilot ratios enables the valve to open based off a given backpressure specific to the application, which could be much lower than the spring pressure setting. This feature allows predictable and consistent control of a load throughout its lowering cycle.
Markets:
• Aerial
• Construction Equipment
• Material Handling Equipment
• Miscellaneous Industrial
• Miscellaneous Mobile
Features/Benefits:
• Hardened, precision ground parts for durability
• Poppet style construction with minimal leakage
• Tamperproof versions available
• Single cartridge valve with integral reverse flow check valve
• Available pilot ratios 8:1 to 1.5:1
• All external parts zinc plated
Applications:
• Load holding
• Position holding
Additional Technical Insight:
The load control valves are load assisted i.e the pilot pressure acts on the difference between the setting and the load at the pilot ratio.
It should always be set at a minimum of 30% higher than the maximum load induced pressure to ensure the valve closes correctly.
Sizing a counterbalance valve needs care in that the flow required is usually higher than system pump flow, as in the case with a cylinder application (retract flow could be twice the system flow) though oversizing the valve could cause instability.
Because of dynamic load variations in many applications, it may be necessary to use a lower pilot ratio or fit an orifice in the pilot line in order to gain stability. The valve will be affected by backpressure and care must be taked with proportional and closed center systems.
Markets:
• Aerial
• Construction Equipment
• Material Handling Equipment
• Miscellaneous Industrial
• Miscellaneous Mobile
Features/Benefits:
• Hardened, precision ground parts for durability
• Poppet style construction with minimal leakage
• Tamperproof versions available
• Single cartridge valve with integral reverse flow check valve
• Available pilot ratios 8:1 to 1.5:1
• All external parts zinc plated
Applications:
• Load holding
• Position holding
Additional Technical Insight:
The load control valves are load assisted i.e the pilot pressure acts on the difference between the setting and the load at the pilot ratio.
It should always be set at a minimum of 30% higher than the maximum load induced pressure to ensure the valve closes correctly.
Sizing a counterbalance valve needs care in that the flow required is usually higher than system pump flow, as in the case with a cylinder application (retract flow could be twice the system flow) though oversizing the valve could cause instability.
Because of dynamic load variations in many applications, it may be necessary to use a lower pilot ratio or fit an orifice in the pilot line in order to gain stability. The valve will be affected by backpressure and care must be taked with proportional and closed center systems.
Port Size | N/A, N/A |
---|---|
Adjustment Mechanism | Fixed, Fixed |
Pilot Pressure Ratio | 7:1, 7:1 |
Seal Material | Fluorocarbon, Fluorocarbon |
Pressure Control Range | 2400-5000 PSI, 166-350 BAR, N/A psi, N/A bar |
Holding Pressure | 3000 PSI, 210 BAR, 210 bar, 3000 psi |
Maximum Flow Rate | 12 GAL/MIN, 45 L/MIN, 45 L/min, 12 Gal/min |
Mounting Type | Threaded Cartridge Valve, Threaded Cartridge Valve |
Maximum Operating Temperature | +400 °F, +204 °C |
Function | Counterbalance Valve |
Maximum Inlet Pressure Rating | 380 bar, 5500 psi |
Minimum Operating Temperature | -26 °C, -15 °F |
Pressure Control Sensitivity | N/A psi, N/A bar |
Flow Rate | 12 Gal/min, 45 L/min |
Actuation Type | Pilot Operated |
Installation Torque | 16 lb-ft, 22 Nm |
Maximum Kinematic Viscosity | 45-2000 SSU (6 to 420 cSt) |
Weight | 0.23 kg, 0.5 lb |
Maximum Operating Pressure | 5000 psi, 350 bar |
Valve Material | All parts steel. All operating parts hardened steel |
Filter Efficiency Rating | ISO 4406 18/16/13, SAE Class 4 |
Cavity Size | C10-3 |
Operating Temperature | -26 to +204 °C, -15 to +400 °F |
Body Material | N/A |
Flow Direction | Cylinder port 1, Valve port 2, Pilot port 3 |
For Fluid Type | Mineral-based or synthetic hydraulic fluids |
Leak Rate | 5 @ 80% of setting drops/min |
Pilot Location | External |
Division | Hydraulic Cartridge Systems Division |